USBridge FirmwareTurn your board into a 60 FPS IP-KVM

Flash a microSD card and turn a Sipeed NanoKVM or a Radxa board into a full IP KVM: 1080p 60 FPS, Moonlight, audio, gamepads and USB passthrough. No ribbon cables, no soldering.

  • 1080p 60Hardware-encoded video
  • 2 minTo flash a microSD card
  • Lifetime licenseNo subscriptions
  • Trial resetRight from the client

Download for free

Open License Manager
Free 24-hour evaluation. Reactivate anytime directly from the device.
Manufacturer:

Board Packages

After flashing: connect to it

Default IP address

10.55.0.1, over the USB cable. Plug the board's USB cable into your computer: the computer gets a USB network adapter (its own internet is untouched) and the KVM is 10.55.0.1 on it. Open http://10.55.0.1 for the setup page: QR code, connect link, key, Moonlight PIN and network settings. On the Sipeed NanoKVM it's always there; on the other boards while the KVM isn't set up yet or has no network address.

On your network (Ethernet, Wi-Fi): the address your router gives it by DHCP, there's no fixed default. The setup page shows it at the top, and so does the front-panel screen on boards with one.

Ways to connect: separate methods, pick one
  1. Recommended, the desktop app: + → Over USB. It finds the KVM on the cable and pairs by itself.
  2. Phone or tablet: open http://10.55.0.1 on the computer the KVM is plugged into and scan its QR code with the mobile app.
  3. Front-panel screen (boards with a screen): Settings → Authentication → Show Master Key, scan the QR code.
  4. Many devices, or the network set before first boot: a provisioning file (usbridge_provision.json). You choose the key and write it into the file; there's no QR code.

No app at hand? The setup page also opens the web client in the browser. The app is recommended: best video and every feature.

Full setup guide →

Free 24-hour evaluation. Reactivate anytime directly from the device.

Open License Manager

Why choose USBridge Firmware for your DIY IP-KVM

Skip the complex wiring and low frame rates. Here is what you get instead.

Instead of PiKVM & DIY Pi builds

No complex ribbon cables or soldering

PiKVM requires a Raspberry Pi, hard-to-find HDMI-to-CSI bridges (TC358743) and a mess of cables totaling $150–$200. With USBridge, a Sipeed NanoKVM has built-in capture, and a Radxa board just needs a simple, cheap USB capture dongle.

Instead of ESP-KVM and LKV373A hacks

Real 1080p 60 FPS streaming, not a slideshow

ESP32 builds and rewired LKV373A extenders lag, drop frames, and cannot carry audio or gamepads. USBridge utilizes the board's hardware video encoder for a silky-smooth, low-latency stream.

Instead of stock firmware limitations

A native client, Moonlight, audio, and gamepads

Stock board firmware is locked to basic keyboard and mouse. USBridge unlocks native client integration, Sunshine/Moonlight streaming, two-way audio, and immutable Btrfs snapshots on the same hardware.

What the firmware adds to your board

1080p at 60 FPS

Hardware-encoded video with low latency, so the remote screen feels like your own.

Moonlight and GameStream host

Any stock Moonlight client can connect to the board and stream the HDMI input, a console included.

Two-way audio

Hear the remote machine and talk back through your microphone.

Gamepads and USB passthrough

Xbox and DualSense controllers and other USB devices work on the remote machine as if plugged into it.

Tailscale P2P built in

An encrypted peer-to-peer connection from anywhere, with no port forwarding and no console setup.

Immutable Btrfs snapshots

The system runs from read-only snapshots, so a bad update or a failed boot rolls back on the next restart.

What you need and a 3-step quick start

What you need

  • A Sipeed NanoKVMThe board with its case. It has a 100 Mbit Ethernet port.
  • A microSD cardIt holds the USBridge image. The stock card stays untouched, so you can swap back any time.
  • An HDMI cableFrom the computer you want to control into the NanoKVM.
  • A USB-C cableFrom the NanoKVM to the computer. It powers the board and carries the keyboard, mouse and virtual drive, so no power adapter is needed.
  • An Ethernet cableFrom the NanoKVM to your router.
  • Optional: Sipeed ATX boardThe ATX power board from Sipeed works with the USBridge firmware too. Wire it to the motherboard's power and reset pins to switch a hung computer on, off and reset it from the client.
ComputerWriting image…DoneSipeed NanoKVMUSBridge192.168.1.42POWERRESETUSB-CLANHDMIUSBRouterUSBridge Client

Write the card

Put the microSD card into your computer, choose Nano KVM and your OS in the download block above and run the command. It writes the USBridge image in about two minutes.

Reviews from owners

Your review

Rating
What you have
Not published, only for checks

By sending, you agree to the privacy policy

USBridge Firmware vs the alternatives

The same job done four ways, from a stock board to a full DIY build.

Stock NanoKVMUSBridge Firmware (DIY)PiKVM DIY (Raspberry Pi + TC358743)ESP-KVM (ESP32)
Total cost~$30–$40~$50–$60 with the $19 license$150+~$25–$35
Setup difficultyReady out of the boxFlash a microSD card in 2 minutesCSI ribbon cables, capture bridge, manual setupSoldering and flashing the ESP32 firmware
Video and FPS1080p, stutters1080p 60 FPS, zero lag1080p, around 30 FPSLow frame rate
Latency150–250 ms45–60 ms——
Video codecH.264, MJPEGH.264 and H.265H.264, MJPEGMJPEG
Audio and gamepadsTwo-way audio, Xbox and DualSense
ATX power control and multi-port KVM switch
Desktop and web clientBrowser onlyDesktop app and web clientBrowser onlyBrowser only
TailscaleBuilt in, but laggyManual setup in the console
OTA updatesThrough the OS package manager
Automation scriptsRadxa boards only

Prices and speeds are approximate and from the makers' public pages and documentation, November 2026. They vary by region and board revision, so check the current figures before you buy. A dash means the feature isn't listed.

Frequently asked questions

Does the firmware support ATX power control (Power and Reset buttons)?

Yes, on the NanoKVM: the ATX power board from Sipeed works with the USBridge firmware. Wire it to the motherboard's power and reset pins and you can switch the computer on, off and reset it from the client, even when it has hung. The Radxa builds control keyboard, mouse and virtual media only.

Can I connect to the board straight from a Moonlight client?

Yes. Add the board in any Moonlight client and enter the PIN on the board's page at http://10.55.0.1. After that it streams like any other Moonlight host, no USBridge Client needed.

How do I go back to the stock firmware?

Keep the stock microSD card and write USBridge to a second one. The board boots from the card, so swapping the cards switches the firmware, and nothing is overwritten.

Can I enable SSH on the board?

Yes. Open http://10.55.0.1 in a browser (the board's page over the USB-C link) and switch SSH on there.

Can I connect it to a multi-port KVM switch, such as an 8-port one?

Yes, in most cases. The board sees one HDMI source and one USB host, which is exactly the computer the switch has selected, so you change computers with the switch's own buttons or hotkeys. Switches that cut the video signal while changing ports may need a moment to reconnect.

Do I need to install anything on the computer I control?

No. The computer sees a regular monitor, keyboard, mouse and USB drive. USBridge Client is installed only on the device you control it from.

How does the 24-hour trial and the $19 license work?

Every feature works free for the first 24 hours, and you can reactivate the evaluation from the device. The $19 license is one-time, not a subscription, and is bound to your board's hardware serial number. After you buy it, it is validated automatically once the board is online.

Which boards are supported?

Sipeed NanoKVM, Radxa Zero 3W, Radxa Zero 3E and Radxa Cubie A7Z. Pick yours in the download block at the top of the page.

Not ready to buy yet? Stay in touch.

News by email

We'll write about new devices and firmware updates.

By subscribing you accept the privacy policy. You can unsubscribe at any time: write to kvm@usbridge.io.

Discord community

Ask questions and see how others set up their KVM.

Go to Discord

Prefer it ready-made?

The same firmware on a KVM that arrives assembled and flashed.